A step-by-step guide on removing and replacing your bath panel

Bath panels are intended to conceal the plumbing that runs underneath your bathtub while also preventing water from getting in there and causing rot or mould to grow, both of which are undesirable outcomes. You'll need one to three panels for your bathtub, one for each side. The number of panels you need is determined by the type of bathtub you have and where it is located in your bathroom. Fitting bath panels UK is a relatively straightforward task, and if you follow our step-by-step guide, you can have the job done quickly. Continue reading to know how to quickly and easily replace an outdated bath panel with a brand-new one.

Instructions for removing a bath panel

It goes without saying that you will need to remove the old bath panel before installing the new one if you are planning on replacing an existing panel. In most cases, this won't require much effort on your part; however, if there is rust or an excessive amount of sealant involved, you may find that you have to put in a little more effort than usual.

Sealant, screws, or both types of fasteners are typically used in conjunction with one another to fasten bath panels into place. Determine which of these two scenarios applies to your home, and then get ready to take off the bath panel:

Removing a panel from an enclosed bath

When cutting through the sealant, a sharp knife or a tool designed specifically for removing sealant should be used. After you have made all of the necessary incisions, you should have no trouble removing the panel once you've finished.

Removing a bath panel that has been screwed in

It is likely that your bath panel is attached to both the wall and the floor by screws; therefore, you will need a screwdriver to remove all of the screws. It's possible that there's also some silicone sealant holding the panel in place; if so, you'll need to cut through the sealant with a knife or a tool designed specifically for removing sealant before you can remove the panel.

The proper way to install a bath panel

Now that you know how to remove the old bath panel, let’s explore how to install a new one. Before we get into the process, ensure that you have all the necessary equipment. The following are the instruments and supplies that you will require:

  • Gloves\ Hacksaw
  • Spirit level
  • Sealant\ Adhesive
  • Wooden battens
  • Brackets
  • Drill or screwdriver 
  • Measuring tape
  • Bath panels accessories: depending on the type of panel

To begin, you will need to take some measurements, starting at the rim of the bathtub and ending at the floor, so that you can determine how high the panel needs to be. It is possible that you will also need to measure the length of the tub if it has an unusual shape.

Cutting

Use your saw to remove any excess panelling. Allow the saw to do the work, and make sure to only push and pull the panel gently and slowly. This will help prevent an uneven cut and damage to the panel, which is especially important when working with an acrylic bath panel.

Then reposition the panel so that it is flush against the bath and use a spirit level to ensure that it is level and will fit properly.

Battens

You'll need wooden battens to connect the two pieces together if you're going to be attaching two panels to one another in order to make an "L" shape out of a side panel and an end panel. If you are going to be using screws, the battens should be made of soft wood that is capable of being easily screwed into the surface. 

Positioning

When your panels are ready, you should test how well they fit against the wall and the bathtub by putting them into position. If you are only replacing one panel, you might find that there is already a batten attached to the wall for you to use as support for securing the new panel. 

Position your panel so that it is flush against the wall, and make a mark at the intersection. After that, take off the panel and position a batten so that it is aligned on the edge of the mark you made underneath the rim of the bathtub. 

Attach

Put some adhesive on the inside of the panel ends, right next to where they will meet the wall batten. Then position your panel where you want it, and attach it to the batten. 

Seal

In the end, a watertight finish can be achieved by applying some silicone sealant to the joints between the panel and the wall and then smoothing it out.

Here are some good panel recommendations that you can include:


#1 Tavistock Meridian Bath Panels

(Source)

This bathroom panel is perfect for you if you are looking for something simple yet elegant. You will get high-quality and sturdy material, so if you go for it, this purchase will surely last for a lifetime!

Product link: https://nationwidebathrooms.com/collections/bath-panels/products/tavistock-meridian-bath-panels


#2 Tavistock Ethos 700 x 500mm Bath End Panels

(Source)

If you like a combination of modern and retro look then this bathroom panel can be your go-to choice! With a wooden texture, this bathroom panel will transform the entire look of your bathroom and give a touch of elegance!

Product link: https://nationwidebathrooms.com/collections/bath-panels/products/tavistock-ethos-bath-panels 

Wrapping Up

People usually rely on professional help to remove and replace their bath panels thinking that it is a very tough job. If you know the right technique then it can be easily done at home. Even before you go out to look for bath panels for sale, it is important to know how to install and replace them. So, to make the whole process easier, do follow this guide and get new bathroom panels installed at your home!
Previous article What Are Bathroom Mixer Taps, and Which Types Can You Purchase?
Next article What is it about glass shower bath screens that make them so popular?